staples vs nails for roof sheathing calculator

Nails vs. Staples | The Building Code Forum- staples vs nails for roof sheathing calculator ,Apr 29, 2010·Utah. Mar 30, 2010. #3. Re: Nails vs. Staples. Ok, here's the way I see it. Table R602.3 (1) requires the sheathing to be attached using 6d, 8d, or 10d depending on the thickness of the sheathing, at 6" O. at panel edges and 12" O in the field. footnote e …Roof Sheathing Fastening Schedules for Wind UpliftROOF SHEATHING FASTENING SCHEDULEa,b,c,d,e 8d Common (0.131 x 2-1/2 inches) or Ring-Shank (0.135 x 2-1/2 inches) (Except Where Noted) for Exposure B, Enclosed Buildings, Roof Framing Spaced 24 inches o. or Less Roof Fastening Zone Wind Main Sheathing-to-Gable- Overhang Velocity Roof End-Wall Framingg (eaves) (3-Second Panel 123 2 3 2 3



Wood Handbook, Chapter 08: Fastenings

Specifying nail sizes by length and diameter dimensions is recommended. Bright box nails are generally of the same length but slightly smaller diameter (Table 8–2), whereas cement-coated nails such as coolers, sinkers, and coated box nails are slightly shorter (3.2 mm (1/8 in.)) and of smaller diameter than common nails of the same penny size.

truss sheathing, nails vs staples - Fine Homebuilding

Mar 17, 2005·truss sheathing, nails vs staples. kkj | Posted in Construction Techniques on March 14, 2005 02:12am. I just had a framer use staples to secure 1/2″ OSB to engineered trusses. Didn’t know anyone did that until today. I though 8d nails, usually galvanized or cement coat was the standard. Am I going to have problems with the staples?

Nails vs. Staples for Shingles | JLC Online

Sep 06, 2018·The staples should also have a minimum crown width of 7/16 inch and should be long enough to penetrate the sheathing 3/4 inch (or all the way through). The same fastener-location guidelines should be followed for staples as for nails: 2 inches above …

Brad Nails vs Staples | DoItYourself

Apr 29, 2010·Brad Nails. The brad nail is a type of finish nail, and like the rest of the family, are used for final work on a project.As they are so small, and may be referred to by the phrase 2d, they are suitable for use in millwork, or on fine-grain wood that will not take a heavier nail.

ROOF SHEATHING FASTENER STUDY

roof sheathing panels of 5/8” thick plywood secured by 1.5” staple legs and 50 full roof sheathing panels of ½” thick plywood secured by the Sheather Plus nail. Sheather Plus nails were driven with a nail gun at 12” on center for the interior and 6” on center around the edges, as prescribed in the current Florida Building Code.

Wood Handbook, Chapter 08: Fastenings

Specifying nail sizes by length and diameter dimensions is recommended. Bright box nails are generally of the same length but slightly smaller diameter (Table 8–2), whereas cement-coated nails such as coolers, sinkers, and coated box nails are slightly shorter (3.2 mm (1/8 in.)) and of smaller diameter than common nails of the same penny size.

Direct withdrawal and head pull-though performance of ...

staples in these new sheathing and siding products is needed for comparative purposes (10). Direct withdrawal resistance of nails and staples is the force required to pull imbedded fasteners from the wood. The holding power of fasteners is especially im-portant when applying shingles or siding materials to roof or wall sheathing (14).

Staples v 8d Common Nails for Sheathing? - Fine Homebuilding

Nov 13, 2004·Considering using a medium crown air stapler for sheathing application. If medium crown (7/16″) power driven staples are use instead of 8d common nails for fastners on roof or wall sheathing (either OSB or plywood), is the nailing schedule the same as code requires for nails. What length of staple should be used (or would this be code specified).

Anatomy of a Staple - SENCO

Jan 11, 2019·Crowning achievement The major difference in staples is the length of the crown, that strip of metal that bridges the staple’s two legs. Crown measurements typically range from 3/16” for projects like molding or trim, where the staple shouldn’t be noticeable, to 1” when visibility isn’t an issue and a heavy-duty hold is needed, such as installation of wire lathing or roofing shingles.

Nails vs. Staples for Shingles | JLC Online

Sep 06, 2018·The staples should also have a minimum crown width of 7/16 inch and should be long enough to penetrate the sheathing 3/4 inch (or all the way through). The same fastener-location guidelines should be followed for staples as for nails: 2 inches above …

Wood Handbook, Chapter 08: Fastenings

Specifying nail sizes by length and diameter dimensions is recommended. Bright box nails are generally of the same length but slightly smaller diameter (Table 8–2), whereas cement-coated nails such as coolers, sinkers, and coated box nails are slightly shorter (3.2 mm (1/8 in.)) and of smaller diameter than common nails of the same penny size.

DuPont Tyvek Protec

2. When attaching DuPont ™ Tyvek ® Protec to the roof sheathing: When used under tile, slate, cedar and metal roof claddings, 1” diameter (min) metal or plastic (ring shank or smooth shank) cap-nails or cap-staples are required. – When used under asphalt or synthetic shingles, 1” diameter (min) metal or plastic cap-nails or capstaples

Size of Roofing Nail??? - Exterior Inspections ...

Jan 02, 2009·Where the roof sheathing is less than 3/4 inch (19.1 mm) thick, the fasteners shall penetrate through the sheathing. Fasteners must comply with ASTM F 1667. Staples are not permitted for shingle application unless specifically noted in the manufacturer’s installation instructions on the shingle package. Use 4 nails for standard installations ...

Roof Sheathing Fastening Schedules for Wind Uplift

ROOF SHEATHING FASTENING SCHEDULEa,b,c,d,e 8d Common (0.131 x 2-1/2 inches) or Ring-Shank (0.135 x 2-1/2 inches) (Except Where Noted) for Exposure B, Enclosed Buildings, Roof Framing Spaced 24 inches o. or Less Roof Fastening Zone Wind Main Sheathing-to-Gable- Overhang Velocity Roof End-Wall Framingg (eaves) (3-Second Panel 123 2 3 2 3

Fastener Calculator | POWERNAIL

Fastener Calculator Follow the Flooring Manufacturers Instructions for Nailing Schedule and Nail Gauge. Nail Schedule 12" Spacing 10" Spacing 8" Spacing 6" Spacing 4" Spacing 3" Spacing

The Problem With Stapled Shingles - Structure Tech

Nov 29, 2011·Today, staples are considered an inferior method of attaching shingles to a roof, but it’s easy to understand why roofers like staples. Staple guns are smaller and better balanced. Coil nail guns are literally fed with a coil of nails, and the holder for the nails makes the gun much bulkier.

DuPont Tyvek Protec

2. When attaching DuPont ™ Tyvek ® Protec to the roof sheathing: When used under tile, slate, cedar and metal roof claddings, 1” diameter (min) metal or plastic (ring shank or smooth shank) cap-nails or cap-staples are required. – When used under asphalt or synthetic shingles, 1” diameter (min) metal or plastic cap-nails or capstaples

cedar shakes: nails vs staples.... | DIY Home Improvement ...

Oct 12, 2006·1,354 Posts. #2 • Oct 12, 2006 (Edited) First i would nail. Two nails per shingle galvanized. Second i would recomend the mesh in between the shingles and the plywood sheathing on the roof. This will extended the shingle life. Third flashing it depends on what needs to be flashed. Some like copper (big money) others just prefer regular ...

Roofing Calculator

Roofing Calculator. The following tools estimate the area of a roof, as well as the amount of materials necessary to construct a roof of a given area. The "House Base Area" is the area of land that the house covers, and for more complex shapes, can be estimated using the Area Calculator.

Nails vs. Screws for Sheathing | JLC Online

Apr 09, 2020·Q: Can screws be used instead of nails for attaching wall sheathing to framing?. A: Roe Osborn, a senior editor at JLC, responds: There is a common misconception in the building industry that screws always outperform nails when attaching wood to wood. It’s true that screws have a highly effective withdrawal resistance, which makes them excellent fasteners for tasks such as avoiding …

Roof Sheathing Calculator - Estimate the Plywood Needed ...

Calculate Sheathing Needed. Once you have the area you can divide by the area of a sheet of plywood to find the number of sheets needed. A 4×8 sheet of plywood is 32 ft 2. So, dividing the area of the roof by 32 will give you the number of sheets needed. For example, if your roof is 1,500 ft 2 then it will take 47 sheets of plywood to sheath it.

cedar shakes: nails vs staples.... | DIY Home Improvement ...

Oct 12, 2006·1,354 Posts. #2 • Oct 12, 2006 (Edited) First i would nail. Two nails per shingle galvanized. Second i would recomend the mesh in between the shingles and the plywood sheathing on the roof. This will extended the shingle life. Third flashing it depends on what needs to be flashed. Some like copper (big money) others just prefer regular ...

Choosing Nails for a Roof: Your Best Options | Findlay Roofing

A proper roofing nail should have a tip that passes about 3/8 of an inch beyond the bottom of the roof sheathing. If you aren’t sure what length sounds right, take a look at your old nails or ask for the opinion of a professional .

Stapling Cedar Siding - JLC-Online Forums

May 21, 2001·In all cases, nails must penetrate solid wood no less than 1 1/2 inches for smooth-shanked nails and 1 1/4 inches for ring or spiral-shanked nails. Given the amount of movement common with cedar siding, and the degree to which staples used in cedar shakes and shingles tend to pull from this movement, I wonder if stainless steel staples would ...

Copyright ©VANQUISH All rights reserved